SC600 (Controller)

SC No.	Type	Error Name/Error Condition/Major Cause/Solution
SC670-01	D	Engine does not startup during the starting up
		/ENGRDY signal was not asserted when the machine was turned on. PCI I/F is not linked up when the machine returns from energy saver mode. EC/PC/SC response was not received within the specified time from power on. Writing to Rapi driver failed (the other party not found through PCI). Connection defect between controller board (PCB15) and BiCU (PCB16). BiCU (PCB16) is down/unstable
		Engine board does not startup.
		Refer to SC670 (engine startup error) is displayed.

SC No.	Type	Error Name/Error Condition/Major Cause/Solution
SC670-02	D	Engine does not start up after the starting up
		CPU reset by software CPU reset by anomaly CPU CPU reset by hardware defect/noise Hardware defect
		Engine board reset unexpectedly.
		Refer to SC670 (engine startup error) is displayed.

SC No.	Type	Error Name/Error Condition/Major Cause/Solution
SC670-03	D	IPU start up error when the machine boots up
		VDET_EPCI signal was not asserted when the machine was turned on.
		IPU, PSU (PCB18), and/or controller board (PCB15) defective Incorrect connection between controller board (PCB15) and IPU. Harness of IPU disconnected
		Refer to SC670 (engine startup error) is displayed.

SC No.	Type	Error Name/Error Condition/Major Cause/Solution
SC670-04	D	Communication error between the engine and controller
		Communication could not linked up.
		IPU and/or controller board (PCB15) defective Incorrect connection between controller board (PCB15) and IPU.
		Refer to SC670 (engine startup error) is displayed.

SC No.	Type	Error Name/Error Condition/Major Cause/Solution
SC670-05	C	Link up error
		Communication could not linked up.
		CTL board defective BiCU (PCB16) defective Incorrect connection between CTL and BiCU (PCB16).
		Logging only.

SC No.	Type	Error Name/Error Condition/Major Cause/Solution
SC672-00	D	Controller startup error
		After the machine was powered on, communication between the controller and the operation panel was not established.
		Controller stalled Board installed incorrectly Controller board (PCB15) defective Operation panel connector loose, broken, or defective Controller late
		Turn the main power OFF/ON. Check the connection of the operation panel. Check the connection of the controller board (PCB15). Replace the controller board (PCB15).

SC No.	Type	Error Name/Error Condition/Major Cause/Solution
SC672-10	D	Controller startup error
		After the machine was powered on, communication between the controller and the operation panel was not established.
		Controller stalled Board installed incorrectly Controller board (PCB15) defective Operation panel connector loose, broken, or defective Controller late
		Turn the main power OFF/ON. Check the connection of the operation panel. Check the connection of the controller board (PCB15). Replace the controller board (PCB15).

SC No.	Type	Error Name/Error Condition/Major Cause/Solution
SC672-11	D	Controller startup error
		After the machine was powered on, communication between the controller and the operation panel was not established, or communication with the controller was interrupted after a normal startup.
		Controller stalled Board installed incorrectly Controller board (PCB15) defective Operation panel connector loose, broken, or defective Controller late
		Turn the main power OFF/ON. Check the connection of the operation panel. Check the connection of the controller board (PCB15). Replace the controller board (PCB15).

SC No.	Type	Error Name/Error Condition/Major Cause/Solution
SC672-12	D	Controller startup error
		Communication with the controller was interrupted after a normal startup.
		Controller stalled Board installed incorrectly Controller board (PCB15) defective Operation panel connector loose, broken, or defective Controller late
		Turn the main power OFF/ON. Check the connection of the operation panel. Check the connection of the controller board (PCB15). Replace the controller board (PCB15).

SC No.	Type	Error Name/Error Condition/Major Cause/Solution
SC672-13	D	Controller startup error
		The operation panel detects that the controller is down due to other reason, shown in SC672-10, SC672-11, and SC672-12.
		Controller stalled Board installed incorrectly Controller board (PCB15) defective Operation panel connector loose, broken, or defective Controller late
		Turn the main power OFF/ON. Check the connection of the operation panel. Check the connection of the controller board (PCB15). Replace the controller board (PCB15).

SC No.	Type	Error Name/Error Condition/Major Cause/Solution
SC672-99	D	Controller startup error
		The operation panel software ended abnormally.
		Controller stalled Board installed incorrectly Controller board (PCB15) defective Operation panel connector loose, broken, or defective Controller late
		Turn the main power OFF/ON. Check the connection of the operation panel. Check the connection of the controller board (PCB15). Replace the controller board (PCB15).