SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC101-01 | D | Lamp Error (Scanning) |
The white level peak did not reach the prescribed threshold when the white guide plate was scanned. Error detection timing;
| ||
| ||
Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC101-02 | D | Lamp Error (Detecting the lighting error) |
The white level peak did not reach the prescribed threshold when the white guide plate was scanned. Error detection timing; During the scanner adjustment (detecting the lighting error) at the time of turning on the scanner (when the main power is turned ON). | ||
| ||
Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC102-00 | D | LED Light Quantity Error |
The white level peak exceeded the prescribed threshold when the white guide plate was scanned. Error detection timing; During the scanner adjustment (detecting the lighting error) at the time of turning on the scanner (when the main power is turned ON). | ||
| ||
Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC111-01 | D | Lamp Error (Scanning) |
The white level peak of the DF did not reach the prescribed threshold when lamp error was detected. Error detection timing;
| ||
| ||
Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC112-00 | D | LED Light Quantity Error (back side) |
The white level peak of the DF white guide plate cannot be adjusted to reach the prescribed threshold when the light error was detected during startup. Error detection timing; During scanner startup (main power was turned on or the machine returned from energy saving mode) | ||
| ||
Check if the SC occurs by turning the main power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC120-00 | D | Scanner Home Position error |
The home position is not correct when the main power is turned ON, at the end of a reading process from the exposure glass and DF. | ||
| ||
| ||
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC141-00 | D | Black level detection error |
The black level cannot be adjusted to the target level at the time of turning on the scanner (when the main power is turned ON). | ||
| ||
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC142-00 | D | White level detection error |
The white level cannot be adjusted to the target level during auto gain control. | ||
| ||
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC144-00 | D | SBU (PCB3) Communication Error |
| ||
| ||
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC151-00 | D | Black level detection error (back side) |
The black level cannot be adjusted to the target level. Error detection timing;
| ||
| ||
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC152-00 | D | White level adjustment error (back side) |
The white level cannot be adjusted to the target level during auto gain control. | ||
| ||
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC154-01 | D | Scanner communication error (back side) |
Error detection timing;
| ||
| ||
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC154-02 | D | Scanner communication error (FPGA) |
Error detection timing;
| ||
| ||
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|
SC No. | Type | Error Name/Error Condition/Major Cause/Solution |
|---|---|---|
SC161-20 | D | Scanner communication error (FPGA) |
Error occured while initializing DDR-PHY and/or TRAINING status confirmation. Error detection timing;
| ||
| ||
Check if the SC occurs by turning the power OFF then ON. If the SC occurs again, do the following steps. Check if the SC reoccurs by cycling the power after each step.
|