1. Remove the rear upper cover [A] from the finisher.
  2. Remove the covers [A], [B], and [C].
  3. Take out the harness [A].

  4. Connect the large connector of the harness [A] to the jogger unit board in the direction as shown below.
    It will be easier to insert the harness by bending it.

  5. Place the harness [A] temporarily as shown below.
    To prevent pinching the harness, make sure that the parts shown in the red circles below fit inside the plate.

  6. Unpack the cooling fan unit.

  7. Position the cooling fan unit upside down, and remove the lower cover [A] from the cooling fan assembly.

  8. Turn over the cooling fan assembly, and remove the screws from the upper cover [A].

  9. Turn over the cooling fan assembly, and then remove the base unit [B] from the upper cover [A].

    Remove the base unit as shown below.

    1. Hold the stay [A] of the base unit, and then rotate the base unit to move three switches [B] out of the upper cover [C].
    2. Hold the stay [A], and then pull out the base unit towards the direction of the arrow.

  10. Remove the bracket [A].

  11. Remove the screw at the center of the paper guide unit which fastens the shaft.

  12. Set the cooling fan unit [A] on the finisher.
    Hook the U shaped grooves of the cooling fan unit over the stepped screws of the jogger unit.

    Make sure that the hooks at the center on the lower side are hooked onto the plate of the jogger unit.

  13. Using the screw removed in step 11, fasten the center of the cover and the shaft of the paper guide unit.

  14. Pass the harness [A] put temporarily in step 5 through the edge saddle and close it. Pull the harness [A] toward you.

  15. Fasten the cooling fan unit with the screws removed in step 2.

  16. Connect the harness [A] to the switch board and clamp it.

  17. Take out the interface unit [A].

  18. Pass the harness [A] of the interface unit through the hole in the bracket [B] removed in step 10. Insert the hook of the harness bracket into the square hole in the bracket [B].

  19. Attach the harness bracket [A] with the silver screw, and pass the harness [B] through the edge saddle.

  20. Route the harness [A] and attach the grounding wire [B] with the blue screw.

  21. Clamp the harnesses.

  22. Attach the bracket [A] with two screws, and connect the cooling fan unit harness to the interface unit harness.

  23. Attach the front cover [A] provided with the cooling fan unit.
  24. Attach the rear cover [A] provided with the cooling fan unit.

  25. Attach the upper cover [A] removed from the base unit of the cooling fan assembly in step 9.
    Use the screws removed in step 8.

    [a]: The frame must be inside the cover.
    [b]: The cover must be inside the frame.

  26. Attach the lower cover [A] removed from the cooling fan assembly in step 7. Use 3x6 screws (accessory #7) for [B]. Insert four hooks into the holes in the upper cover.



    [a]: The lower cover must be inside the upper cover.

    If the screw hole shown in the red circle is too high or too low, press the cord [B] with your finger and adjust the position of the hole.

  27. Attach the finisher rear upper cover [A] removed in step 1.

  28. Pro C5200S/C5210S only: Remove the connector cover [A] from the main machine.

    Check the positions of the hooks before removing the connector cover.

  29. Remove the upper screw [A] from the rear lower cover.
  30. Peel off the tapes from the Velcro [B] attached to the interface unit [A] (accessory #2).
  31. Align the screw hole [C] with the screw hole in the cover [A], and attach the interface unit [B] with its Velcro against the surface of the cover.
  32. Attach the interface unit [A] to the lower left cover with an M3x16 screw (accessory #6).

  33. Connect the interface unit cable [A] to the copier.

  34. Bind the harness of the interface unit [A] and clamp it with Locking Wire Saddle CKN-13 [B] (accessory #5).

    • Depending on the number of options installed between the copier and Finisher, 3 pcs of Locking Wire Saddle CKN-13 might be needed to clamp the harness.