• When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.

  • This option cannot be used together with the following peripherals:
    - Internal Shift Tray SH3070 (D691)
    - Side Tray Type M3 (D725)
    - Internal Finisher SR 3130 (D690)
    - Bridge Unit BU3070 (D685)
    - Internal Multi-Fold Unit FD3000 (D3E4)
  • For using this option together with "1 Bin Tray BN3110 (D3CQ)", attach the bottom plate of this option at the beginning, then install the "1 Bin Tray BN3110 (D3CQ)", followed by installing this option.

  1. Remove the orange tape and shipping retainers.
  2. Remove the knob screw and red tag [A] ( x 1).
  3. Remove the shaft [B] from the slide rail [A] ( x 1).
  4. Remove the paper exit cover [A] ( x 2).
  5. Place the slide rail [A] under the internal finisher [B].
  6. Insert the shaft [A] into the holes in the slide rail and internal finisher, and then fasten with the screw ( x 1).
  7. Attach the paper exit cover (removed in step 4) [A] ( x 2).
  8. Remove the paper exit tray [A].
  9. Remove the paper exit feeler [A].
  10. Tuck in the lever [A] for detecting when the tray is full.
  11. Open the front cover, and then remove the left upper cover [A] ( x 1).
  12. Release the hooks [A], and remove the left rear cover [B].
  13. Remove the inverter tray [A] and tray support plate [B] ( x 1).

  14. Open the right cover, and then remove the upper front cover [A].

    • When removing the upper front cover, release the hooks at the back of the cover.
    • Tilt the operation panel [B] upward to a horizontal position, and then remove the upper front cover [A].

  15. Remove the paper exit cover [A] ( x 1).
  16. Remove the connector cover [A].

  17. Remove the paper exit lower cover [A].

    • The lower inside cover can be removed together with the paper exit lower cover, because the inside cover is secured to the paper exit lower cover with three screws.

  18. Remove the lower inside cover [B] from the paper exit lower cover [A] ( x 2).
  19. Remove the fixing screws on the upper inside cover [A].
  20. Remove the upper inside cover [A].
  21. Insert the bottom plate [A] into the holes.
  22. Install the bottom plate [A] (x 3, Accessory No. 7).
  23. Install the lower inside cover (removed in step 18) [A] in the finisher (x 2, Accessory No.5).
  24. Reattach the upper inside cover (removed in step 20) [A] (x 2).

  25. Reattach the paper exit cover [A] and the connector cover [B] (removed in step 15 and step 16).

    • Touching the moving parts inside of the cover can result in an injury. To avoid this, be sure to install the connector cover [B].

  26. Reattach the tray support plate (removed in step 13) [A] ( x 1).
  27. Reattach the covers (removed in step 14 and step 15), and close the right door.

  28. Remove the driven roller [B] at the machine’s exit tray and attach the supplied driven roller [A].

    • Insert a flathead screwdriver into the depression in the center, and then, lifting the driven roller, unlock the part indicated by the red arrow.
    • When attaching the driven roller, push its center all the way in until it clicks.


    [A]: The supplied driven roller has flat rollers.

    [B]: The machine’s standard driven roller has drum-type rollers (as indicated by the red frames).

  29. Attach the paper support guide [A] (Tab x 4)

  30. Install the internal finisher [A].

  31. Secure the finisher ( x 1, Accessory No.8).
  32. Attach the left upper cover [A] and the left rear cover [B] (removed in step 11 and step 12).
  33. Attach the left lower cover [A] ( x 2, Accessory No.6).
  34. Attach the paper exit tray ( x 2, Accessory No.4).
  35. Reattach the inverter tray [A] removed in step 13.
  36. Connect the interface cable [A].
  37. Attach the nylon clamp [A] as shown below (Accessory No.9).
  38. Turn ON the main power.
  39. Ensure that the operation panel displays finisher jobs properly and that it works properly.