• The machine should be held at the correct locations and lifted gently by two people.
  • If it is lifted without care, handled carelessly or dropped, it may result in injury.
  • When installing this option, turn the machine power OFF, and unplug the power supply cord from the wall socket.
  • If this option is installed with the power on, it may result in an electric shock or a malfunction.
  • Be sure to join the machine to the paper feed unit so as to prevent equipment from falling over.
  • If they are not connected, they may move and fall over, resulting in injury.

  • The Paper Feed Unit PB3150 does not have casters. Attach the “Caster Table Type M3” under the Paper Feed Unit PB3150, if necessary. (Caster Table Type M3 (D178))

  1. Remove the orange tape and retainers.
  2. Remove the items provided (fixing screws, etc.) from the package.
  3. Install this option on the Caster Table (Caster Table Type M3 (D178)).

  4. Holding the grips on the machine, align it with the locating pins [A], and place the machine on the paper feed unit.

    • When you lift the machine, hold the correct locations.
    • Do not hold any other parts of the machine when lifting it, because this may cause the machine to deform.
    • Do not put the machine down on the paper feed unit as a temporary resting place. This may cause the paper feed unit to deform. Always connect the machine and paper feed unit properly.

  5. Pull out the 2nd paper feed tray of the main machine.
  6. Using a securing bracket as a screwdriver, fix the machine to the feed unit (spring washer: screw: M4×10: 1).
  7. Attach the securing brackets [A] to two positions on the left and right at the rear of the machine.
  8. Attach the rear lower gap cover [A] (x 2)
  9. Return the paper feed tray to the machine.

  10. Attach the decals as shown below.

    [A]: Tray number decal
    [B]: Paper size decal

    • The tray number decal and paper size decal are packaged together with the machine.

  11. Lock the casters.

  12. Connect the power cord to the machine.

    • Stabilizers are attached to the paper feed unit when it is shipped. Do not remove them.

  13. Turn the main power switch ON.
  14. Set the paper, and check that the paper size set in the paper feed tray is displayed on the operation panel.
    • Paper size for the paper feed unit can be changed with following SP.
      SP5-181-009 (0: A4 LEF or 1: LT LEF)
      SP5-181-010 (0: A3 or 1: DLT)
      SP5-181-011 (0: B4 or 1: LG)
      SP5-181-012 (0: B5 LEF or 1: Exe LEF)

  15. Adjust the registration for the paper feed unit.
    SP1-001-0xx (Leading Edge Registration Tray 3)

    -055

    Tray3: Thin

    -062

    Tray3: Thin:1200

    -056

    Tray3: Plain

    -063

    Tray3: Plain:1200

    -057

    Tray3: Mid-thick

    -064

    Tray3: Mid-thick:1200

    -058

    Tray3: Thick 1

    -065

    Tray3: Thick 1:1200

    -059

    Tray3: Thick 2

    -066

    Tray3: Thick 2:1200

    -060

    Tray3: Thick 3

    -067

    Tray3: Thick 3:1200

    -061

    Tray3: Thick 4

    -068

    Tray3: Thick 4:1200

    SP1-002-004 (Side-to-Side Registration Paper Tray 3)