• The machine should be held at the correct locations and lifted gently.
  • If it is lifted without care, handled carelessly or dropped, it may result in an injury.
  • When installing this option, turn the machine power OFF, and unplug the power supply cord from the wall socket.
  • If this option is installed with the power on, it may result in an electric shock or a malfunction.
  • Be sure to join the machine to the paper feed unit so as to prevent equipment from falling over.
  • If they are not connected, they may move and fall over, resulting in injury.

  1. Remove the orange tape and retainers.
  2. Remove the items provided (fixing screws, etc.) from the package.

  3. Holding the grips on the machine, align it with the locating pins [A], and place the machine on the paper feed unit.

    • When you lift the machine, hold the correct locations.
    • Do not hold any other parts of the machine when lifting it, because this may cause the machine to deform.
    • Do not put the machine down on the paper feed unit as a temporary resting place. This may cause the paper feed unit to deform. Always connect the machine and paper feed unit properly.

  4. Pull out the 2nd paper feed tray.
  5. Using a securing bracket as a screwdriver, fix the machine to the feed unit (spring washer: screw: M4×10: 1).

  6. Attach the securing brackets [A] to two positions on the left and right at the rear of the machine (screws: 1 each).


  7. Attach the rear lower gap cover [A] (x 2)
  8. Return the paper feed tray to the machine

  9. Attach the decals as shown below.

    [A]: Tray number decal
    [B]: Paper size decal

    • The tray number decal and paper size decal are packaged together with the machine.

  10. Lock the casters of the paper feed unit.

  11. Connect the power cord to the machine.

    • Stabilizers are attached to the machine when it is shipped. Do not remove them.

  12. Turn the main power ON.
  13. Set the paper, and check that the paper size set in the paper feed tray is displayed on the operation panel.
    • Paper size for the paper feed unit can be changed with following SPs.
      SP5-181-009 (0: A4 LEF or 1: LT LEF) for Tray 3
      SP5-181-010 (0: A3 or 1: DLT) for Tray 3
      SP5-181-011 (0: B4 or 1: LG) for Tray 3
      SP5-181-012 (0: B5 LEF or 1: Exe LEF) for Tray 3
      SP5-181-014 (0: A4 LEF or 1: LT LEF) for Tray 4
      SP5-181-015 (0: A3 or 1: DLT) for Tray 4
      SP5-181-016 (0: B4 or 1: LG) for Tray 4
      SP5-181-017 (0: B5 LEF or 1: Exe LEF) for Tray 4
  14. Adjust the registration for the paper feed unit.

    • For Tray 3
      SP1-001-0xx (Leading Edge Registration Tray 3)

      -055

      Tray3: Thin

      -062

      Tray3: Thin:1200

      -056

      Tray3: Plain

      -063

      Tray3: Plain:1200

      -057

      Tray3: Mid-thick

      -064

      Tray3: Mid-thick:1200

      -058

      Tray3: Thick 1

      -065

      Tray3: Thick 1:1200

      -059

      Tray3: Thick 2

      -066

      Tray3: Thick 2:1200

      -060

      Tray3: Thick 3

      -067

      Tray3: Thick 3:1200

      -061

      Tray3: Thick 4

      -068

      Tray3: Thick 4:1200

      SP1-002-004 (Side-to-Side Registration Paper Tray 3)

    • For Tray 4
      SP1-001-0xx (Leading Edge Registration Tray 4)

      -069

      Tray4: Thin

      -076

      Tray4: Thin:1200

      -070

      Tray4: Plain

      -077

      Tray4: Plain:1200

      -071

      Tray4: Mid-thick

      -078

      Tray4: Mid-thick:1200

      -072

      Tray4: Thick 1

      -079

      Tray4: Thick 1:1200

      -073

      Tray4: Thick 2

      -080

      Tray4: Thick 2:1200

      -074

      Tray4: Thick 3

      -081

      Tray4: Thick 3:1200

      -075

      Tray4: Thick 4

      -082

      Tray4: Thick 4:1200

      SP1-002-005 (Side-to-Side Registration Paper Tray 4)