SC No.

Type

Error Name/Error Condition/Major Cause/Solution

SC561-01

A

Pressure Roller Thermistor (Center) Disconnection

SC561-05

D

Pressure Roller Thermistor (Center) Disconnection (Low Power)

  

Below 0 degree C is detected for 20 sec. continuously.

Detection period: 100 ms, detection frequency: 10 times or more.

  
  • Non-contact thermistor disconnection
  • Connector disconnected
  • Harness disconnection in the fusing unit
  • Harness disconnection inside the main machine
  • BCU defective

  • Fusing lamp defective

  • AC controller board defective
  
  1. Check the power supply voltage and reconnect the cable to the outlet. (-05 only)
  2. Reconnect the connectors (between the fusing unit and the BCU). 
  3. Replace the thermistor.
  4. Replace the fusing unit.
  5. Replace the harness between the fusing unit and the BCU or the PSU (AC controller board)..
  6. Replace the BCU.
  7. Replace the fusing sleeve belt unit.
  8. Replace the PSU (AC controller board).

SC No.

Type

Error Name/Error Condition/Major Cause/Solution

SC562-02

A

Pressure Roller Thermistor (Center) Does Not Reload

  

Does not reach 40 degree C after fusing lamp 1ON for 12 sec.

SC562-05

D

Pressure Roller Thermistor (Center) Does Not Reload (Low Power)

  

-

  
  • Outside input voltage guarantee
  • Thermistor dirt
  • Thermistor deformed or not installed (or mounted) properly
  • After excessive temperature rise prevention unit operation
  • Fusing lamp disconnection
  • Harness disconnection inside the main machine
  • Thermopile defective
  • BCU defective
  • AC controller board defective
  
  1. Check the power supply voltage and reconnect the cable to the outlet.
  2. Clean or replace the thermistor.
  3. Replace the fusing sleeve thermostat.
  4. Replace the fusing sleeve belt unit.
  5. Replace the harness between the fusing unit and the BCU or the PSU (AC controller board).
  6. Replace the thermopile (center).
  7. Replace the BCU.
  8. Replace the PSU (AC controller board).

SC No.

Type

Error Name/Error Condition/Major Cause/Solution

SC563-00

A

Pressure Roller Thermistor (Center) High Temperature Detection (software)

  

Above 230 degrees C detected for 1sec. continuously.

Detection period: 100ms, detection count: 10 times or more.

  

  • Paper setting misdetection

  • Incorrect paper position in the paper feed tray

  • Jammed paper between the center thermopile and fusing unit
  • Thermopile lens dirt
  • Thermopile deformed or not installed (or mounted) properly
  • Harness disconnection inside the main machine
  • Triac defective (short-circuit)
  • BCU failure
  • AC controller board failure
  
  1. Check the paper settings.

  2. Check the paper position in the paper feed tray.

  3. Reconnect the connectors (between the fusing unit and the BCU).
  4. Remove the jammed paper between the center thermopile and fusing unit.
  5. Clean or replace the thermopile (center).
  6. Replace the harness between the fusing unit and the BCU or the PSU (AC controller board).
  7. Replace the BCU.
  8. Replace the PSU (AC controller board).
    If the problem cannot be solved after performing the above steps, replace the fusing unit.

SC No.

Type

Error Name/Error Condition/Major Cause/Solution

SC564-00

A

Pressure Roller Thermistor (Center) High Temperature Detection (hardware)

  

Above 240 degrees C detected

  

  • Paper setting misdetection

  • Incorrect paper position in the paper feed tray

  • Jammed paper between the center thermopile and fusing unit
  • Thermopile lens dirt
  • Thermopile deformed or not installed (or mounted) properly
  • Pressure roller HP sensor disconnected
  • Harness disconnection inside the main machine
  • Triac defective (short-circuit)
  • BCU failure
  • AC controller board failure
  
  1. Check the paper settings.

  2. Check the paper position in the paper feed tray.

  3. Reconnect the connectors (between the fusing unit and the BCU).
  4. Remove the jammed paper between the center thermopile and fusing unit.
  5. Clean or replace the thermopile (center).
  6. Inspect the pressure roller HP sensor with SP5-803-047.
  7. Replace the harness between the fusing unit and the BCU or the PSU (AC controller board).
  8. Replace the BCU.
  9. Replace the PSU (AC controller board).
    If the problem cannot be solved after performing the above steps, replace the fusing unit.

SC No.

Type

Error Name/Error Condition/Major Cause/Solution

SC569-00

D

Paper Exit/ Pressure Release Motor Error Detection

Retry operation fails 3 times consecutively.

  • Pressure roller HP sensor disconnected
  • Pressure release encoder deformed
  • Fusing unit defective
  • Paper exit/ pressure release motor disconnected

Inspect the pressure roller HP sensor with SP5-803-047. If there is no response from the sensor, perform steps 1 and 2.

  1. Check the connection of the pressure roller HP sensor.
  2. Inspect the pressure roller HP sensor.
  3. Inspect the pressure release encoder.
  4. Replace the fusing unit.
  5. Check the connectors of the paper exit/ pressure release motor.