- When installing this option, turn OFF the main power and unplug the power cord from the wall socket. If installing without turning OFF the main power, an electric shock or a malfunction may occur.
- Be careful not to get your finger caught in the area indicated by the red frame (this is where the tray rotates up and slides in).
- Open the by-pass tray, and then attach the sub tray [A]. (Rivet x2)
- Fold the sub-tray.
- Remove the packing tape attached on the main tray (1), and pull out the belt (2).
While pressing down the feeler [B] on the bypass tray, push the main tray [A] into the bypass tray to attach it.
When you attach the tray, hold it with both hands to make sure that it does not fall.- Check if the locks on the main tray’s sides are engaged.
- Check if the locks on the main tray’s sides are engaged.
- Attach the belt by engaging it with the hooks [A].
- Remove the backing paper for the double-sided tapes on the lock plate.
- Adjust the position of the lock plate so that its center is aligned with the tab [1] on the machine’s right cover.
Hang the lock plate’s top part on the right cover (
) and affix the lock plate (
).
- Tuck in the banner paper guide tray [A] and turn the lock plate’s knob to lock it.
- The double-sided adhesive tapes stick firmly in about one day.
- When replacing the parts of the Banner Paper Guide Tray, use the installation procedure above in reverse order as a reference in order to make it easier to disassemble the unit.
Confirming the Banner Counter SP settings
Explain this counter specification change to the customer when installing the Banner Paper Guide Tray or changing these settings. The banner counter counts up 1 every threshold length when the paper length is more than 488mm.
Banner counter is controlled by the following SP and SSPs
| SP No. | SP Name | Function | Min to Max/Int./Step |
|---|---|---|---|
| 5-104-001 | A3/DLT Double Count | Selects whether or not to count A3/DLT as A4 x 2 (double count). | 0 or 1/1/1 0: OFF |
| 5-104-101 (SSP) | Banner Count Setting | Selects whether or not to activate the count setting when an output paper size is longer than 488mm. | 0 or 1/1/1 0: OFF 1: ON |
| 5-104-102 (SSP) | Banner Count Threshold | Specifies the threshold length for counting up when SP5-104-101 is set to "1". The default setting is 200mm. | 0 to 65535/200/1 |
The count-up condition can be changed with the use of these Super SPs and the A3/DLT Couble Count SP as follows. Please set these Super SPs and SP to the values which are designated by sales staff.
Important: When SP5-104-001 is "1(ON)", counts up 2 for paper length between 391 mm and 488mm.
| Case 1: Counts up 1 for all paper lengths. | Case 2: Counts up 2 for all paper lengths bigger than 391mm. | Case 3: Counts up 2 for all paper lengths bigger than 488mm. | Case 4: Counts up 2 for paper length between 391 and 488mm. Counts up 1 more for every 200mm over 488mm. | Case 5: Counts up 2 for paper length between 391 and 488mm. Counts up 1 more for every 350mm over 488mm. |
| SP5-104-001 | 0 (OFF) | 1 (ON) | 0 (OFF) | 1(ON) Default | 1(ON) |
SP5-104-101 (SSP) | 0 (OFF) | 0 (OFF) | 1 (ON) | 1(ON) Default | 1(ON) |
SP5-104-102 (SSP) | Not used (Any value is OK.) | Not used (Any value is OK.) | 0 | 200 Default | 350 |