The yield figures in the above table are based on the following conditions:
- A4 (LT) long-edge feed
- 5% image coverage ratio
- Color ratio: 30% (IM C6000/C5500/C4500/C3500/C3000), 20% (IM C2500/C2000)
- 3 prints/job (IM C3500/C3000), 4 prints/job (IM C6000/C5500/C4500), 2 prints/job (IM C2500/C2000)
- Environment: Normal temperature and humidity
Yield may change depending on circumstances and print conditions.
Symbol keys:
C: Clean, R: Replace, L: Lubricant, I: Inspect
Item | EM parts
| Cycle | Remarks |
|---|---|---|---|
PCDU | |||
PCU(K) C6000/C5500/C4500 C3500/C3000 | R 400K | ||
PCU(K) C2500/C2000 | R 60K | ||
PCU(C,M,Y) C6000/C5500/C4500 | R 270K | ||
PCU(C,M,Y) C3500/C3000 | R 175K | ||
PCU(C,M,Y) C2500/C2000 | R 48K* | *P/J | |
Waste Toner Bottle | R 100K | Full detection is a mechanical detection by the feeler. Replace when waste toner bottle full is detected. | |
Development Unit (K) C6000/C5500/C4500 C3500/C3000 | R 600K | ||
Development Unit (K) C2500/C2000 | R 180K | ||
Development Unit (C,M,Y) C6000/C5500/C4500 | R 270K | ||
Development Unit (C,M,Y) C3500/C3000 | R 160K | ||
Development Unit (C,M,Y) C2500/C2000 | R 120K | ||
PCDU (K) C6000/C5500/C4500 C3500/C3000 | R 400K* | *P/J | |
PCDU (K) C2500/C2000 | R 60K* | *P/J | |
PCDU (C, M, Y) C6000/C5500/C4500
| R 270K* | *P/J | |
PCDU (C, M, Y) C3500/C3000 | R 160K* | *P/J | |
PCDU (C, M, Y) C2500/C2000 | R 48K* | *P/J | |
Transfer | |||
Image Transfer Cleaning Unit C6000/C5500/C4500 C3500/C3000 | R 600K* | *P/J | |
Image Transfer Cleaning Unit C2500/C2000 | R 240K* | *P/J | |
Image Transfer Belt Unit C6000/C5500/C4500 C3500/C3000 | R 600K | ||
| Image Transfer Belt Unit C2500/C2000 | R 240K | ||
Paper Transfer Roller C6000/C5500/C4500 C3500/C3000 | R 900K
| ||
Paper Transfer Roller C2500/C2000 | R 240K
| ||
Fusing | |||
Heating Sleeve Belt Unit C6000/C5500/C4500 C3500/C3000 | R 400K | ||
Heating Sleeve Belt Unit C2500/C2000 | R 240K | ||
Pressure Roller C6000/C5500/C4500 C3500/C3000 | R 400K | ||
Pressure Roller C2500/C2000 | R 240K | ||
Bearing: Fusing Roller C6000/C5500/C4500 C3500/C3000 | R 400K | Lubricating grease | |
Bearing: Fusing Roller C2500/C2000 | R 240K | ||
Thermopile | C 400K | Dry cloth | |
Fusing unit C6000/C5500/C4500 C3500/C3000 | R 400K* | *P/J | |
Fusing unit C2500/C2000 | R 240K* | *P/J | |
Miscellaneous | |||
Ozone filter/Dust filter | R 400K | ||
| Waste Toner Bottle | R 100K* | *Image Coverage ratio |
Yield Parts
- Some of the parts mentioned in these tables have a target yield. However, the total copy/print volume made by the machine will not reach the target yield within the machine's targeted lifetime if the machine is used under the target usage conditions (ACV, color ratio, P/J, and C/O). So, these parts are categorized not as PM parts but as yield parts (EM parts).
- PCU and Development unit is replaced together as PCDU. Individual parts are registered for EM replacement.
- ITB cleaning unit is integrated into ITB Unit. Individual part is registered for EM replacement.
Fusing section is replaced as Fusing Unit. Individual parts are registered for EM replacement.
- When the fusing unit is used past its target yield (400k/240k), the fusing belt may break, causing a service call. Therefore, it is designed that the machine starts displaying a stop warning on the operation panel at 415k/244k pages and stops at 430k/248k pages. Please make sure to replace the fusing belt unit before the unit's PM counter reaches 430k/248k pages.
- A customer replaces the Waste Toner Bottle. By changing SP5-073-001, service replace mode for Waste Toner Bottle is enabled. Never try to empty toner out of the waste toner bottle to use the same bottle again; always replace the bottle with a new one. This is because the transfer coil inside the bottle may break.