1001 | [Bit Switch] | |||
001 | Bit Switch 1 Settings | 0 | 1 | |
bit 0 | DFU | - | - | |
bit 1 | Responding with the hostname as the sysName | Model name (PnP name) | Hostname | |
This BitSwitch can change the value of the sysName. 0 (default): Model name (PnP name) such as "SP C352DN" 1: Host name | ||||
bit 2 | DFU | - | - | |
bit 3 | No I/O Timeout | Disabled | Enabled | |
Enables/Disables I/O Timeouts. If enabled, the I/O Timeout setting will have no affect. I/O Timeouts will never occur. | ||||
bit 4 | SD Card Save Mode | Disabled | Enabled | |
If this bit switch is enabled, print jobs will be saved to the GW SD slot and not output to paper. | ||||
bit 5 | [PS and PDF] Paper size error margin | ±5pt | ±10pt | |
When a PS job is printed by using a custom paper size, the job might not be printed because of a paper size mismatch caused by a calculation error. By default, the error margin for matching to a paper size is ±5 points. By enabling this BitSwitch, the error margin for matching to a paper size can be extended to ±10 points. | ||||
bit 6 | Color balance switching | 0:Disabled | 1:Enabled | |
This BitSwitch can be used to restore the color balance to match that of previous models. If this BitSwitch is set to "1" (Enabled), the color balance that is equivalent to Fuji-Xerox printers will be used. | ||||
bit 7 | [RPCS,PCL]: Printable area frame border | Disabled | Enabled | |
Prints all RPCS and PCL jobs with a border around the printable area. | ||||
1001 | [Bit Switch] | |||
002 | Bit Switch 2 Settings | 0 | 1 | |
bit 0 | Color balance switching | Disabled | Enabled | |
This BitSwitch can be used to restore the color balance to match that of previous models. If this BitSwitch is set to "1" (Enabled), the color balance from 09S and earlier models will be used.
| ||||
bit 1 | RPCS: Switching between normal printing mode and 2-color printing mode for color absence prevention | OFF (Normal mode) | ON (Color absence prevention mode) | |
bit 2 | DFU | - | - | |
bit 3 | [PCL5e/c,PS]: PDL Auto Switching | Enabled | Disabled | |
Enables/Disables the machine's ability to change the PDL processor mid-job. Some host systems submit jobs that contain both PS and PCL5e/c. If Auto PDL switching is disabled, these jobs will not be printed properly. | ||||
bit 4 | Color balance switching | Disabled | Enabled | |
This BitSwitch can be used to restore the color balance to match that of previous models. If this BitSwitch is set to "1" (Enabled), the color balance from 09A and Extended 09A models will be used.
| ||||
bit 5 | DFU | - | - | |
bit 6 | Switch dither *Please refer to RTB#RD014018 | Use normal dither | Use alternative dither | |
bit 7 | Switching of in-process print mode | Normal mode | In-process mode | |
1001 | [Bit Switch] | |||
003 | Bit Switch 3 Settings | 0 | 1 | |
bit 0 | RPDL/R98/R55/R16: Switching font size of OCR-B | OFF (Conventional font size) | ON (New font size) | |
bit 1 | RPDL: Switching ON/OFF the display of "86%" option in the "Scaling" menu of the printing condition settings | OFF (Not displayed) | ON (Displayed) | |
bit 2 | [PCL5e/c]: Legacy HP compatibility | Disabled | Enabled | |
Uses the same left margin as older HP models such as HP4000/HP8000. In other words, the left margin defined in the job (usually "<ESC>*r0A") will be changed to "<ESC>*r1A". | ||||
bit 3 | RPGL: Switching ON/OFF the "Reduce the line width of 0.3 mm or thicker pens by 1 dot" function for color machine | (Do not reduce by 1 dot) | ON (Reduce by 1 dot) | |
bit 4 | RPDL, R16, R55, R98, GL/GL2: Ignore one byte in data greater than 0x80 when the host power is turned ON | OFF (Do not ignore) | ON (Ignore) | |
bit 5 | RPDL: Selection of paper feed tray allocation | LP type | MFP type | |
bit 6 | R16, R55, R98: Selection of paper feed tray allocation | LP type | MFP type | |
bit 7 | DFU | - | - | |
1001 | [Bit Switch] | |||
004 | Bit Switch 4 Settings | 0 | 1 | |
bit 0 | RPDL, R16, R55, R98: Fill enclosed areas of simple graphics | OFF (Do not fill) | ON (Fill) | |
bit 1 | R98: Avoid clearing 2-byte external characters | OFF (Clear) | ON (Do not clear) | |
bit 2 | R16: Avoid resetting portrait/landscape settings by reset command | OFF | ON | |
bit 3 | DFU | - | - | |
bit 4 | RPDL, R16, R55, R98, GL/GL2: Hide/show the display of error messages No. 84 to DF | OFF (Display) | ON (Do not display) | |
bit 5 | RPDL, R16, R55, R98, GL/GL2: Hide/show the display of error messages No. E1 onwards | OFF (Display) | ON (Do not display) | |
bit 6 | DFU | - | - | |
bit 7 | DFU | - | - | |
1001 | [Bit Switch] | |||
005
| Bit Switch 5 Settings | 0 | 1 | |
bit 0 | DFU | - | - | |
bit 1 | Multiple copies if a paper size or type mismatch occurs | Disabled (single copy) | Enabled (multiple) | |
If a paper size or type mismatch occurs during the printing of multiple copies, only a single copy is output by default. Using this BitSw, the device can be configured to print all copies even if a paper mismatch occurs. | ||||
bit 2 | Prevent SDK applications from altering the contents of a job. | Disabled | Enabled | |
If this switch is enabled, SDK applications will not be able to alter print data. This is achieved by preventing SDK applications from accessing a module called the "GPS Filter". Note: The main purpose of this switch is for troubleshooting the effects of SDK applications on data. | ||||
bit 3 | [PS] PS Criteria | Pattern3 | Pattern1 | |
Change the number of PS criterion used by the PS interpreter to determine whether a job is PS data or not. Pattern3: includes most PS commands. Pattern1: A small number of PS tags and headers | ||||
bit 4 | Increase max number of the stored jobs. | Disabled (100) | Enabled (750) | |
Changes the maximum number of jobs that can be stored on the HDD. The default (disabled) is 100. If this is enabled, the max. will be raised to 750. | ||||
bit 5 | DFU | - | - | |
1001 | [Bit Switch] | |||
005 | Bit Switch 5 Settings | 0 | 1 | |
bit 6 | Method for determining the image rotation for the edge to bind on. | Disabled | Enabled | |
If enabled, the image rotation will be performed as they were in the specifications of older models for the binding of pages of mixed orientation jobs. The old models are below: - PCL: Pre-04A models - PS/PDF/RPCS:Pre-05S models | ||||
bit 7 | Letterhead mode printing | Disabled | Enabled (Duplex) | |
Routes all pages through the duplex unit. If this is disabled, simplex pages or the last page of an odd-paged duplex job, are not routed through the duplex unit. This could result in problems with letterhead/pre-printed pages. Only affects pages specified as Letterhead paper. | ||||
1001 | [Bit Switch] | ||
006 | Bit Switch 6 Settings DFU | - | - |
1001 | [Bit Switch] | |||
007 | Bit Switch 7 Settings | 0 | 1 | |
bit 0 | DFU | - | - | |
bit 1 | MSIS: Setting to LT-size medical receipt continuation sheet mode | Normal mode (11"x8.5") | Receipt continuation sheet mode (239 mm x 210 mm | |
bit 2 | RPDL: Addition of 3 characters for ruling line | Not added | Added | |
bit 3 | RPCS: Inhibition of overwrap judgment process | Not inhibited | Inhibited | |
bit 4 | RPCS: Inhibition of Black Over Print | Not inhibited | Inhibited | |
bit 5 | DFU | - | - | |
bit 6 | MSIS: Insert a blank back page when performing duplex printing of an odd number of pages | Inserted | Not inserted | |
bit 7 | DFU | - | - | |
1001 | [Bit Switch] | |||
008 | Bit Switch 8 Settings | 0 | 1 | |
bit 0 | MSIS: Enable switching of binding margin position in the same duplex printing job Enable switching of binding position on a per-page basis in a duplex printing job | Enabled DAZEL mode Compatible with non-GW machine (Switching enabled) | Disabled (Switching disabled) | |
If the function is enabled, "Switching of binding margin position in the same duplex printing job" will also work. | ||||
bit 1 | MSIS/RPCS: Count data indicated in debug messages | Disabled | Enabled | |
bit 2 | R16, R55, R98: Setting the scope of 11-inch settings | A4 landscape 67x67% is set as scope of 11-inch settings | Not set (Compatible with former models) | |
bit 3 | [PCL,PS]: Allow BW jobs to print without requiring User Code | Disabled | Enabled (allow BW jobs to print without a user code) | |
BW jobs submitted without a user code will be printed even if usercode authentication is enabled. Note: Color jobs will not be printed without a valid user code. | ||||
bit 4 | PCL: Switching to custom-built EdgeToEdge (Tailored to BMS) | Disabled (Normal EdgeToEdge is applied) | Enabled (Custom-built EdgeToEdge is applied) | |
Valid only for PCL5 | ||||
1001 | [Bit Switch] | |||
008 | Bit Switch 8 Settings | 0 | 1 | |
bit 5 | RTIFF (TIFFDP): Switching of default values of printing conditions | Default values for model 07A series and later | Default values for model 06A series and earlier | |
bit 6 | PCL, RPCS, PS: Forced BW print | Enabled | Disabled | |
Switches whether to ignore PDL color command. | ||||
bit 7 | RTIFF (TIFFDP): Switching of image rotation angle | Disabled | Enabled MSIS compatible mode | |
If the orientation of an image does not match that of the sheet, the angle of the image can be changed. If the function is disabled, the angle of the image will be kept at 270°. With the function enabled, the image will be rotated by 90° only if the following criteria are met: -The machine is capable of rotating expanded images. -Printing conditions allow rotation of expanded images. -Limitless paper feed is enabled or finishing process is disabled. -In the orientation setting menu, 90° or 180° is selected. | ||||
1001 | [Bit Switch] | |||
009
| Bit Switch 9 Settings | 0 | 1 | |
bit 0 | PDL Auto Detection timeout of jobs submitted via USB or Parallel Port (IEEE 1284). | Disabled (Immediately) | Enabled (10 seconds) | |
To be used if PDL auto-detection fails. A failure of PDL autodetection doesn't necessarily mean that the job can't be printed. This bit switch tells the device whether to time-out immediately (default) upon failure or to wait 10 seconds. | ||||
bit 1 | DFU | - | - | |
bit 2 | Job Cancel | Disabled (Not cancelled) | Enabled (Cancelled) | |
If this bit switch, all jobs will be cancelled after a jam occurs. Note: If this bitsw is enabled, printing under the following conditions might result in problems: - Job submission via USB or Parallel Port - Spool printing (WIM >Configuration > Device Settings > System) | ||||
bit 3 | DFU | - | - | |
bit 4 | Timing of the PJL Status ReadBack (JOB END) when printing multiple collated copies. | Disable | Enable | |
This switch determines the timing of the PJL USTATUS JOB END sent when multiple collated copies are being printed. 0 (default): JOB END is sent by the device to the client after the first copy has completed printing. This causes the page counter to be incremented after the first copy and then again at the end of the job. 1: JOB END is sent by the device to the client after the last copy has finished printing. This causes the page counter to be incremented at the end of each job. | ||||
1001 | [Bit Switch] | |||
009 | Bit Switch 9 Settings | 0 | 1 | |
bit 5 | Display UTF-8 text in the operation panel | Enabled | Disabled | |
Enabled (=0): Text composed of UTF-8 characters can be displayed in the operation panel. Disabled (=1): UTF-8 characters cannot be displayed in the operation panel. For example, job names are sometimes stored in the MIB using UTF-8 encoded characters. When these are displayed on the operation panel, they will be garbled unless this switch is enabled (=0). | ||||
bit 6 | Disable super option | OFF | ON | |
Switches super option disable on / off. If this is On, multiple jobs are grouped at LPR port. PJL settings are enabled even jobs that are specified queue names are sent. | ||||
bit 7 | Enable/Disable Print from USB/SD's Preview function | Enabled | Disabled | |
Determines whether Print from USB/SD will have the Preview function. Enabled (=0): Print from USB/SD will have the Preview function. Disabled (=1): Print from USB/SD will not have the Preview function. | ||||
1001 | [Bit Switch] | |||
010
| Bit Switch A Settings | 0 | 1 | |
bit 0 | DFU | - | - | |
bit 1 | DFU | - | - | |
bit 2 | DFU | - | - | |
bit 3 | DFU | - | - | |
bit 4 | DFU | - | - | |
bit 5 | Store and Skip Errored Job locks the queue | Queue is not locked after SSEJ | Queue locked after SSEJ | |
If this is 1, then after a job is stored using Store and Skip Errored Job (SSEJ), new jobs cannot be added to the queue until the stored job has been completely printed. | ||||
bit 6 | Allow use of Auto Job Promotion if connected to an external charge device. | Does not allow AJP with ECD | Allows AJP with ECD | |
If this is 0, Auto Job Promotion will be automatically disabled if an external charge device is connected. Note: We do not officially support enabling this switch (1). Use it at your own risk. | ||||
bit 7 | DFU | - | - | |
1001 | [Bit Switch] | |||
011 | Bit Switch B Settings | 0 | 1 | |
bit 0 | DFU | - | - | |
bit 1 | Print job interruption | Does not allow interruption | Allow interruption | |
0 (default): Print jobs are not interrupted. If a job is promoted to the top of the print queue, it will wait for the currently printing job to finish. 1: If a job is promoted to the top of the queue, it will interrupt the currently printing job and start printing immediately. | ||||
bit 2 | In the manual feed free mode, the manual feed tray is included within/excluded from the scope of the limitless paper feed function | Included within scope | xcluded from scope | |
bit 3 | DFU | - | - | |
bit 4 | Add/do not add tray lock to tray overwriting criteria | Do not add | Add | |
bit 5 | DFU | - | - | |
bit 6 | Disable/do not disable the selection of trays that are not included in the choices of automatic tray selection in the Forced Print screen | Do not disable | Disable | |
bit 7 | DFU | - | - | |
1001 | [Bit Switch] | |||
012 | Bit Switch C Settings | 0 | 1 | |
bit 0 | DFU | - | - | |
bit 1 | DFU | - | - | |
bit 2 | DFU | - | - | |
bit 3 | DFU | - | - | |
bit 4 | DFU | - | - | |
bit 5 | Change the user ID type displayed on the operation panel | Login User Name | User ID | |
As of 15S models, the Login User Name can be displayed on the operation panel. The user ID type displayed on the operation panel can be changed by configuring BitSwitch #12-5 as follows: - 0 (default): Login User Name - 1: User ID. If this is enabled, User ID will be displayed, which is equivalent to the behavior exhibited in 14A and earlier models. | ||||
bit 6 | Ability to use AirPrint | Enabled | Disabled | |
For 15S and later models that support AirPrint, AirPrint can be disabled by changing this Bit Switch from 0 (default) to 1. | ||||
Bit 7 | DFU | |||
1003 | [Clear Setting] | ||
1-003-001 | Initialize Printer System | *CTL | [- / - / -] [Execute] |
Initializes settings in the "System" menu of the user mode. | |||
1-003-003 | Delete Program | *CTL | [- / - / -] [Execute] |
1004 | [Print Summary] | ||
Prints the service summary sheet (a summary of all the controller settings). | |||
1-004-001 | Print Printer Summary | CTL | [- / - / -] [Execute] |
1007 | [Supply Display] | ||
Sets displaying remaining supply amount information or not. 0: Displays remaining supply amount information 1: Does not display remaining supply amount information | |||
1-007-001 | Development | *CTL | [0 or 1 / 1 / 1 /step] *The Default setting is 1 but the Factory setting is 0 |
1-007-002 | PCU | *CTL | |
1-007-003 | Transfer | *CTL | |
1-007-004 | Int. Transfer | *CTL | |
1-007-005 | Transfer Roller | *CTL | |
1-007-006 | Fuser | *CTL | |
1-007-007 | Fuser Oil | *CTL | |
1101 | [Data Recall] | ||
Recalls a set of gamma settings. This can be either a) the factory setting, b) the previous setting, or c) the current setting. | |||
1-101-001 | Factory | *CTL | [ - / - / - ] [Execute] |
1-101-002 | Previous | *CTL | |
1-101-003 | TCurrent | *CTL | |
1102 | [Resolution Setting] | ||
Selects the printing mode (resolution) for the printer gamma adjustment. | |||
1-102-001 | Tone Control Media Selection | CTL | [0 to 7 / 0 / 1/step] 0: 1200x1200Photo 1: 600x600Photo 2: 600x600 Photo 3: 600x600 Photo 4: 1200x1200 Text 5: 600x600 Text 6: 600x600 Text 7: 600x600 Text |
1103 | [Test Page] | ||
Prints the test page to check the color balance before and after the gamma adjustment. | |||
1-103-001 | Color Gray Scale | CTL | [ - / - / - ] [Execute] |
1-103-002 | Color Pattern | CTL | |
1104 | [Gamma Adjustment] | ||
Adjusts the printer gamma for the mode selected in the "Mode Selection" menu. | |||
1-104-001 | Black 1: Highlight | CTL | [0 to 255 / 0 / 1/step ] |
1-104-002 | Black 2: Shadow | CTL | |
1-104-003 | Black 3: Middle | CTL | |
1-104-004 | Black 4: IDmac | CTL | |
1-104-005 | Tone Control Value Setting: Black 5 | CTL | |
1-104-006 | Tone Control Value Setting: Black 6 | CTL | |
1-104-007 | Tone Control Value Setting: Black 7 | CTL | |
1-104-008 | Tone Control Value Setting: Black 8 | CTL | |
1-104-009 | Tone Control Value Setting: Black 9 | CTL | |
1-104-010 | Tone Control Value Setting: Black 10 | CTL | |
1-104-011 | Tone Control Value Setting: Black 11 | CTL | |
1-104-012 | Tone Control Value Setting: Black 12 | CTL | |
1-104-013 | Tone Control Value Setting: Black 13 | CTL | |
1-104-014 | Tone Control Value Setting: Black 14 | CTL | |
1-104-015 | Tone Control Value Setting: Black 15 | CTL | |
1-104-021 | Cyan 1: Highlight | CTL | [0 to 255 / 0 / 1/step ] |
1-104-022 | Cyan 2: Shadow | CTL | |
1-104-023 | Cyan 3: Middle | CTL | |
1-104-024 | Cyan 4: IDmac | CTL | |
1-104-025 | Tone Control Value Setting: Cyan 5 | CTL | |
1-104-026 | Tone Control Value Setting: Cyan 6 | CTL | |
1-104-027 | Tone Control Value Setting: Cyan 7 | CTL | |
1-104-028 | Tone Control Value Setting: Cyan 8 | CTL | |
1-104-029 | Tone Control Value Setting: Cyan 9 | CTL | |
1-104-030 | Tone Control Value Setting: Cyan 10 | CTL | |
1-104-031 | Tone Control Value Setting: Cyan 11 | CTL | |
1-104-032 | Tone Control Value Setting: Cyan 12 | CTL | |
1-104-033 | Tone Control Value Setting: Cyan 13 | CTL | |
1-104-034 | Tone Control Value Setting: Cyan 14 | CTL | |
1-104-035 | Tone Control Value Setting: Cyan 15 | CTL | |
1-104-041 | Magenta 1: Highlight | CTL | [0 to 255 / 0 / 1/step ] |
1-104-042 | Magenta 2: Shadow | CTL | |
1-104-043 | Magenta 3: Middle | CTL | |
1-104-044 | Magenta 4: IDmac | CTL | |
1-104-045 | Tone Control Value Setting: Magenta 5 | CTL | |
1-104-046 | Tone Control Value Setting: Magenta 6 | CTL | |
1-104-047 | Tone Control Value Setting: Magenta 7 | CTL | |
1-104-048 | Tone Control Value Setting: Magenta 8 | CTL | |
1-104-049 | Tone Control Value Setting: Magenta 9 | CTL | |
1-104-050 | Tone Control Value Setting: Magenta 10 | CTL | |
1-104-051 | Tone Control Value Setting: Magenta 11 | CTL | |
1-104-052 | Tone Control Value Setting: Magenta 12 | CTL | |
1-104-053 | Tone Control Value Setting: Magenta 13 | CTL | |
1-104-054 | Tone Control Value Setting: Magenta 14 | CTL | |
1-104-055 | Tone Control Value Setting: Magenta 15 | CTL | |
1-104-061 | Yellow 1: Highlight | CTL | [0 to 255 / 0 / 1/step ] |
1-104-062 | Yellow 2: Shadow | CTL | |
1-104-063 | Yellow 3: Middle | CTL | |
1-104-064 | Yellow 4: IDmac | CTL | |
1-104-065 | Tone Control Value Setting: Yellow 5 | CTL | |
1-104-066 | Tone Control Value Setting: Yellow 6 | CTL | |
1-104-067 | Tone Control Value Setting: Yellow 7 | CTL | |
1-104-068 | Tone Control Value Setting: Yellow 8 | CTL | |
1-104-069 | Tone Control Value Setting: Yellow 9 | CTL | |
1-104-070 | Tone Control Value Setting: Yellow 10 | CTL | |
1-104-071 | Tone Control Value Setting: Yellow 11 | CTL | |
1-104-072 | Tone Control Value Setting: Yellow 12 | CTL | |
1-104-073 | Tone Control Value Setting: Yellow 13 | CTL | |
1-104-074 | Tone Control Value Setting: Yellow 14 | CTL | |
1-104-075 | Tone Control Value Setting: Yellow 15 | CTL | |
1105 | [Save Tone Control Value] | ||
Stores the print gamma adjusted with the "Gamma Adj." menu item as the current setting. Before the machine stores the new "current setting", it moves the data currently stored as the "current setting" to the "previous setting" memory storage location. | |||
1-105-001 | Save Tone Control Value | *CTL | [ - / - / - ] [Execute] |
1106 | [Toner Limit] | ||
Adjusts the maximum toner amount for image development. | |||
1-106-001 | Toner Limit Value | *CTL | [0 to 400 / 0 / 1 %/step ] |
1109 | [EconomyColor] | ||
Adjusts the maximum toner amount for image development. | |||
1-109-001 | Text | *CTL | [0 to 999 / 100 / 1 /step ] |
1-109-002 | Image | *CTL | [0 to 999 / 50 / 1 /step ] |
1-109-003 | Line | *CTL | [0 to 999 / 30 / 1 /step ] |
1-109-004 | Paint | *CTL | [0 to 999 / 30 / 1 /step ] |
1110 | [Media Print Device Setting] | ||
Selects the setting for the media print device. | |||
1-110-002 | 0: Disable 1: Enable | *CTL | [0 or 1 / 1 / 1 /step] |
1111 | [All Job Delete Mode]] | ||
Selects whether to include an image processing job in jobs subject to full cancellation from the SCS job list. | |||
1-111-001 | 0: Excluding New Job 1: Including New Job | *CTL | [0 or 1 / 1 / 1 /step] |
1112 | [Operation when detecting that the supply has run out] | |
Selects whether or not to stop at once or continue printing even on detecting that the supply has run out. | ||
1-112-001 | - | [0 or 1 / 0 / 1/step] |
1113 | [IBACC Exec] | ||
Sets IBACC correction execution (calculation IBACC gamma) on / off. 0: Not calculate IBACC gamma. (Sets IBACC gamma linear) 1: Calculate IBACC gamma | |||
1-113-001 | 0:Off 1:On | *CTL | [0 or 1 / 1 / 1/step] |
1114 | [IBACC ToneCtlSet] | ||
Sets back to the previous value of IBACC gamma correction for all resolutions. If there is no previous value, sets to the factory default values. | |||
1-114-001 | Tone (Prev.) | CTL | - |
1-114-002 | Tone (Factory) | CTL | - |
1115 | [IBACC Exec Time] | ||
Displays the time when IBACC is executed or sets back to the previous / initial value. | |||
1-115-001 | Time | CTL | - |
1115 | [IBACC Data Copy] | |
Copies the IBACC data file (ibacc.dat) stored in the flash memory to the microSD card. | ||
1-115-002 | - | [0 or 1 / 1 / 1/step] |
1121 | [Initial settings menu ON/OFF] | ||
Select whether or not to display the initial settings (such as the language, time zone, and summer time settings) when turning the power on for the first time. 0: Not displayed 1: Displayed | |||
1-121-001 | Time | CTL | - |