5804 | [OUTPUT CHECK] | ||
5-804-003 | BWMT_Plain | ENG | [0 or 1 / 0 / 1/step] When using this SP, remove Bk toner cartridge / Bk PCDU. Toner may contaminate inside of the machine. |
5-804-004 | BWMT_Thick1 | ENG | |
5-804-005 | BWMT_Thick2 | ENG | |
5-804-010 | FUMT_Plain | ENG | [0 or 1 / 0 / 1/step] |
5-804-011 | FUMT_Thick1 | ENG | [0 or 1 / 0 / 1/step] |
5-804-013 | FUMT_Thick2 | ENG | [0 or 1 / 0 / 1/step] |
5-804-017 | COLMT_Plain | ENG | [0 or 1 / 0 / 1/step] When using this SP, remove FC (CMY) toner cartridge / FC (CMY) PCDU. Toner may contaminate inside of the machine. |
5-804-018 | COLMT_Thick1 | ENG | |
5-804-019 | COLMT_Thick2 | ENG | |
5-804-024 | MIDMT_Plain | ENG | [0 or 1 / 0 / 1/step] When using this SP, remove all toner cartridges / all PCDU. This may damage PCDU and transfer belt, and would affect printing images. |
5-804-025 | MIDMT_Thick1 | ENG | |
5-804-026 | MIDMT_Thick2 | ENG | |
5-804-035 | FEEDMT_1TCSP | ENG | [0 or 1 / 0 / 1/step] Revolve using transected motor speed of the 1st transfer. When using this SP, remove all toner cartridges / all PCDU. This may damage PCDU and transfer belt, and would affect printing images. |
5-804-036 | FEEDMT_HANDBP | ENG | [0 or 1 / 0 / 1/step] To lift manual feed base plate, reverse drive paper transfer motor, and rotate at a speed for lifting. When using this SP, remove all toner cartridges / all PCDU. This may damage PCDU and transfer belt, and would affect printing images. |
5-804-039 | REG_CL | ENG | [0 or 1 / 0 / 1/step] |
5-804-040 | MID_CL | ENG | [0 or 1 / 0 / 1/step] |
5-804-041 | PAP_CL | ENG | [0 or 1 / 0 / 1/step] |
5-804-042 | HAND_CL | ENG | [0 or 1 / 0 / 1/step] |
5-804-043 | DUP_MID_CL | ENG | [0 or 1 / 0 / 1/step] |
5-804-044 | DUP_OUT_CL | ENG | [0 or 1 / 0 / 1/step] |
5-804-046 | PAPOUT_SOL | ENG | [0 or 1 / 0 / 1/step] Drives solenoid for the idler gear to reverse drive paper exit roller. 0: Off 1: On – idler gear works to transfer the paper to the duplex unit. Do not turn on more than a minute, this might damage the machine because of the high heat. |
5-804-047 | HAND_BP_CL | ENG | [0 or 1 / 0 / 1/step] |
5-804-083 | 1TCSP_CL | ENG | [0 or 1 / 0 / 1/step] |
5-804-091 | TN_CL_K | ENG | [0 or 1 / 0 / 1/step] |
5-804-092 | TN_CL_C | ENG | [0 or 1 / 0 / 1/step] |
5-804-093 | TN_CL_M | ENG | [0 or 1 / 0 / 1/step] |
5-804-094 | TN_CL_Y | ENG | [0 or 1 / 0 / 1/step] |
5-804-100 | MIN_FAN_H | ENG | [0 or 1 / 0 / 1/step] |
5-804-101 | MIN_FAN_L | ENG | [0 or 1 / 0 / 1/step] |
5-804-102 | FU_FAN_H | ENG | [0 or 1 / 0 / 1/step] |
5-804-103 | FU_FAN_L | ENG | [0 or 1 / 0 / 1/step] |
5-804-107 | PSU_FAN_H | ENG | [0 or 1 / 0 / 1/step] |
5-804-108 | PSU_FAN_L | ENG | [0 or 1 / 0 / 1/step] |
5-804-130 | HVP_C_K | ENG | [0 or 1 / 0 / 1/step] 0: Off 1: On – Output -1100V There is no SP to change output voltage. When turning this ON, make sure to remove Bk toner cartridge and Bk PCDU. OPC Drum might be scratched by the discharge. SP5804-147 must be ON to output voltage. |
5-804-131 | HVP_C_C | ENG | [0 or 1 / 0 / 1/step] 0: Off 1: On – Output -1100V There is no SP to change output voltage. When turning this ON, make sure to remove Cy toner cartridge and Cy PCDU. OPC Drum might be scratched by the discharge. SP5804-148 must be ON to output voltage. |
5-804-132 | HVP_C_M | ENG | [0 or 1 / 0 / 1/step] 0: Off 1: On – Output -1100V There is no SP to change output voltage. When turning this ON, make sure to remove Ma toner cartridge and Ma PCDU. OPC Drum might be scratched by the discharge. SP5804-148 must be ON to output voltage. |
5-804-133 | HVP_C_Y | ENG | [0 or 1 / 0 / 1/step] 0: Off 1: On – Output -1100V There is no SP to change output voltage. When turning this ON, make sure to remove Ye toner cartridge and Ye PCDU. OPC Drum might be scratched by the discharge. SP5804-148 must be ON to output voltage. |
5-804-134 | HVP_DV_K | ENG | [0 or 1 / 0 / 1/step] 0: Off 1: On – Output -200V There is no SP to change output voltage. SP5804-147 must be ON to output voltage. |
5-804-135 | HVP_DV_C | ENG | [0 or 1 / 0 / 1/step] 0: Off 1: On – Output -200V There is no SP to change output voltage. SP5804-148 must be ON to output voltage. |
5-804-136 | HVP_DV_M | ENG | |
5-804-137 | HVP_DV_Y | ENG | |
5-804-138 | HVP_DV_+ | ENG | [0 or 1 / 0 / 1/step] 0:OFF 1:ON |
5-804-139 | HVP_T1_K | ENG | [0 or 1 / 0 / 1/step] 0: Off 1: On – Output +1000V There is no SP to change output voltage. |
5-804-143 | HVP_T2_+ | ENG | [0 or 1 / 0 / 1/step] 0: Off 1: On – Output +30uA There is no SP to change output value. |
5-804-144 | HVP_T2_- | ENG | [0 or 1 / 0 / 1/step] 0: Off 1: On – Output -800V There is no SP to change output voltage. |
5-804-147 | HVP_BION_BK | ENG | [0 or 1 / 0 / 1/step] SP to output charging and development for Bk. This SP must be “ON” to enable SP5804-130 / SP5804-134 to output voltage. |
5-804-148 | HVP_BION_COL | ENG | [0 or 1 / 0 / 1/step] SP to output charging and development for Bk. This SP must be “ON” to enable SP5804-135 to SP5804-137 to output voltage. |
5-804-185 | TM_0 | ENG | [0 or 1 / 0 / 1/step] |
5-804-186 | TM_1 | ENG | [0 or 1 / 0 / 1/step] |
5-804-190 | QLON_BK | ENG | [0 or 1 / 0 / 1/step] |
5-804-191 | QLON_COL | ENG | [0 or 1 / 0 / 1/step] |
5-804-224 | BANK_MT1:Plain | ENG | [0 or 1 / 0 / 1/step] |
5-804-225 | BANK_MT1:Thick1 | ENG | [0 or 1 / 0 / 1/step] |
5-804-226 | BANK_MT1:Thick2 | ENG | [0 or 1 / 0 / 1/step] |
5-804-227 | BANK_MT2:Plain | ENG | [0 or 1 / 0 / 1/step] |
5-804-228 | BANK_MT2:Thick1 | ENG | [0 or 1 / 0 / 1/step] |
5-804-229 | BANK_MT2:Thick2 | ENG | [0 or 1 / 0 / 1/step] |
5-804-230 | BANK_MT3:Plain | ENG | [0 or 1 / 0 / 1/step] |
5-804-231 | BANK_MT3:Thick1 | ENG | [0 or 1 / 0 / 1/step] |
5-804-232 | BANK_MT3:Thick2 | ENG | [0 or 1 / 0 / 1/step] |
5-804-239 | BANK_PAP_CL1 | ENG | [0 or 1 / 0 / 1/step] |
5-804-240 | BANK_PAP_CL2 | ENG | [0 or 1 / 0 / 1/step] |
5-804-241 | BANK_PAP_CL3 | ENG | [0 or 1 / 0 / 1/step] |
5-804-242 | BANK_FEED_CL1 | ENG | [0 or 1 / 0 / 1/step] |
5-804-243 | BANK_FEED_CL2 | ENG | [0 or 1 / 0 / 1/step] |
5-804-244 | BANK_FEED_CL3 | ENG | [0 or 1 / 0 / 1/step] |
5-804-248 | ON_DEMAND_2 | ENG | [0 or 1 / 0 / 1/step] Do not execute. |
5-804-249 | MIDFU_NEWON | ENG | [0 or 1 / 0 / 1/step] 0: Off 1: On – flows current to cut the new detection fuse of the Fusing unit. This SP only flows current, no new detection control is working. |
5-804-250 | PCDU_NEWON | ENG | [0 or 1 / 0 / 1/step] |
5-804-251 | TEON_BK | ENG | [0 or 1 / 0 / 1/step] |
5-804-252 | TEON_COL | ENG | [0 or 1 / 0 / 1/step] |
5-804-253 | UPCOVER_SOL | ENG | [0 or 1 / 0 / 1/step] This SP controls shutter to supply toner to PCDU from toner cartridge. If top cover is opened, it is a spec not to open shutter. Must to hear the sound to check if this solenoid is working. When using this SP, remove all toner cartridge / PCDU. Toner may contaminate inside of the machine. |
5-804-254 | 5V_TMP_ON | ENG | [0 or 1 / 0 / 1/step] This SP supplies power to the thermopile to check the surface temperature of fusing belt. Design analysis use only. Controlling this SP might damage the thermopile. |
| 5-804-255 | BankSerialComm | ENG | [0 or 1 / 0 / 1/step] |
6012 | [ADF OUTPUT Check] | ||
| 6-012-003 | Motor Forward | ENG | [0 or 1 / 0 / 1/step] |
| 6-012-004 | Motor Reverse | ENG | [0 or 1 / 0 / 1/step] |
| 6-012-014 | Feed Clutch | ENG | [0 or 1 / 0 / 1/step] |