Top Page > SC Codes > Service Call 700-740 > SC700 (Engine: Peripherals) > Multi-Folding Unit

Multi-Folding Unit

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-01	D	Downstream device communication error
		Downstream device break continued even after 10 sec passes. Partner terminal does not break even 200 msec after the downstream device starts to wait. ATN without break is received in advance from the downstream device. ST2 is received from the downstream device during receipt of ST1 frame, or vice versa. When the response (ACKn) to the frame sent to the downstream device is not notified within the time limit (100 msec), frame sending is retried a maximum of 3 times but there is still no responses acquired. After connection with the downstream device, the downstream device breaks again.
		Interface cable (downstream device side) connector disconnected or broken PCB of downstream device defective Controller PCB defective
		Replace the interface cable. Replace the PCB of downstream device. Replace the controller board.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-03	D	Multi-Folding Unit: Protection device break error 1
		A fuse has blown on the 24V1 line.
		24V2 line fuse blown
		Replace the Main Board.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-04	D	Multi-Folding Unit: Protection device break error 2
		A fuse has blown on the 24V2 line.
		24V2 line fuse blown
		Replace the Main Board.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-12	B	Registration Roller Transport Motor Error
		Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat
		Replace the Main Board. Replace the Registration Roller Transport Motor. Replace the harness.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-13	B	Dynamic Roller Transport Motor Error
		Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat
		Replace the Main Board. Replace the Dynamic Roller Transport Motor Replace the harness.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-14	B	Top Tray Exit Motor Error
		Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat
		Replace the Main Board. Replace the Top Tray Exit Motor. Replace the harness.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-30	B	Stopper 1 Motor Error
		When moving to the home position, home position was not detected within specified number of pulses. (The first time: jam display, the second time: SC) When moving from the home position, home position was still detected after specified number of pulses. (The first time: jam display, the second time: SC) Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat Connector disconnected
		Replace the Main Board. Replace the Stopper 1 Motor. Replace the harness. Reconnect the connector. Replace the Stopper 1 HP Sensor

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-31	B	Stopper 2 Motor Error
		When moving to the home position, home position was not detected within specified number of pulses. (The first time: jam display, the second time: SC) When moving from the home position, home position was still detected after specified number of pulses. (The first time: jam display, the second time: SC) Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat Connector disconnected
		Replace the Main Board. Replace the Stopper 2 Motor. Replace the harness. Reconnect the connector. Replace the Stopper 2 HP Sensor.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-32	B	Stopper 3 Motor Error
		When moving to the home position, home position was not detected within specified number of pulses. (The first time: jam display, the second time: SC) When moving from the home position, home position was still detected after specified number of pulses. (The first time: jam display, the second time: SC) Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat Connector disconnected
		Replace the Main Board. Replace the Stopper 3 Motor. Replace the harness. Reconnect the connector. Replace the Stopper 3 HP Sensor.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-33	B	Jogger Fence Motor Error
		When moving to the home position, home position was not detected within specified number of pulses. (The first time: jam display, the second time: SC) When moving from the home position, home position was still detected after specified number of pulses. (The first time: jam display, the second time: SC) Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat Connector disconnected
		Replace the Main Board. Replace the Jogger Fence Motor. Replace the harness. Reconnect the connector. Replace the Jogger Fence HP Sensor.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-34	B	Dynamic Roller Lift Motor Error
		When moving to the home position, home position was not detected within specified number of pulses. (The first time: jam display, the second time: SC) When moving from the home position, home position was still detected after specified number of pulses. (The first time: jam display, the second time: SC) Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat Connector disconnected
		Replace the Main Board. Replace the Dynamic Roller Lift Motor Replace the harness. Reconnect the connector. Replace the Dynamic Roller HP Sensor.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-35	B	Registration Roller Release Motor Error
		When moving to the home position, home position was not detected within specified number of pulses. (The first time: jam display, the second time: SC) When moving from the home position, home position was still detected after specified number of pulses. (The first time: jam display, the second time: SC) Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat Connector disconnected
		Replace the Main Board. Replace the Registration Roller Release Motor. Replace the harness. Reconnect the connector. Replace the Jogger Fence HP Sensor.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-36	B	Direct-Send JG Motor Error
		When moving to the home position, home position was not detected within specified number of pulses. (The first time: jam display, the second time: SC) When moving from the home position, home position was still detected after specified number of pulses. (The first time: jam display, the second time: SC) Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat Connector disconnected
		Replace the Main Board. Replace the Direct-Send JG Motor. Replace the harness. Reconnect the connector. Replace the Direct Send JG HP Sensor.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-37	B	FM6 Pawl Motor Error
		When moving to the home position, home position was not detected within specified number of pulses. (The first time: jam display, the second time: SC) When moving from the home position, home position was still detected after specified number of pulses. (The first time: jam display, the second time: SC) Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat Connector disconnected
		Replace the Main Board. Replace the FM6 Pawl Motor. Replace the harness. Reconnect the connector. Replace the Bypass Exit Paper Sensor.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-38	B	Fold Plate Motor Error
		When moving to the home position, home position was not detected within specified number of pulses. (The first time: jam display, the second time: SC) When moving from the home position, home position was still detected after specified number of pulses. (The first time: jam display, the second time: SC) Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat Connector disconnected
		Replace the Main Board. Replace the Fold Plate Motor. Replace the harness. Re-connect the connector. Replace the Fold Plate HP Sensor.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-39	B	1st Fold Motor Error
		Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat
		Replace the Main Board. Replace the 1st Fold Motor. Replace the harness.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-40	B	2nd Fold Motor Error
		Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat
		Replace the Main Board. Replace the 2nd Fold Motor Replace the harness.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-41	B	Crease Motor Error
		Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat
		Replace the Main Board. Replace the Crease Motor. Replace the harness.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-71	D	Horizontal Transport Motor Error
		Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat
		Replace the Main Board. Replace the Horizontal Transport Motor Replace the harness.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-72	D	Horizontal Exit Motor Error
		Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat
		Replace the Main Board. Replace the Horizontal Exit Motor. Replace the harness.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-73	D	Top Tray Transport Motor Error
		Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat
		Replace the Main Board. Replace the Top Tray Transport Motor Replace the harness.

SC No.	Level	Error Name/Error Condition/Major Cause/Solution
SC725-74	D	Entrance JG Motor Error
		When moving to the home position, home position was not detected within specified number of pulses. (The first time: jam display, the second time: SC) When moving from the home position, home position was still detected after specified number of pulses. (The first time: jam display, the second time: SC) Motor driver detected an error. (SC from the first time)
		Overcurrent to the motor. Motor drive overheat Connector disconnected
		Replace the Main Board. Replace the Entrance JG Motor Replace the harness. Re-connect the connector. Replace the Entrance JG HP Sensor.